View MAX9914EXKT_1208365.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

general description the single max9914/max9915 and dual max9916/ max9917 operational amplifiers feature maximized ratio of gain bandwidth to supply current and are ideal for battery-powered applications such as portable instru- mentation, portable medical equipment, and wireless handsets. these cmos op amps feature an ultra-low 1pa input bias current, rail-to-rail inputs and outputs, low 20? supply current, and operate from a single 1.8v to 5.5v supply. for additional power conservation, the max9915/max9917 feature a low-power shutdown mode that reduces supply current to 1na, and puts the amplifier outputs in a high-impedance state. these devices are unity-gain stable with a 1mhz gain-band- width product. the max9914 and max9915 are available in 5-pin and 6-pin sc70 packages, respectively. the max9916 is available in an 8-pin sot23 package, and the max9917 in a 10-pin ?ax package. all devices are specified over the -40 c to +85 c extended operating temperature range. applications portable medical devices portable test equipment rf tags laptops data-acquisition equipment features ? high 1mhz gbw ? ultra-low 20a supply current ? single 1.8v to 5.5v supply voltage range ? ultra-low 1pa input bias current ? rail-to-rail input and output voltage ranges ? low 200v input offset voltage ? low 0.001a shutdown current ? high-impedance output during shutdown (max9915/max9917) ? unity-gain stable ? available in tiny sc70, sot23, and max packages max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown ________________________________________________________________ maxim integrated products 1 19-3407; rev 1; 10/05 for pricing, delivery, and ordering information, please contact maxim/dallas direct! at 1-888-629-4642, or visit maxim? website at www.maxim-ic.com. ordering information part temp range pin- package top mark max9914 exk+t -40? to +85? 5 sc70-5 agb max9914exk-t -40? to +85? 5 sc70-5 agb max9915 ext+t -40? to +85? 6 sc70-6 acb max9915ext-t -40? to +85? 6 sc70-6 acb max9916 eka+t -40? to +85? 8 sot23-8 aejz max9916eka-t -40? to +85? 8 sot23-8 aejz max9917 eub -40? to +85? 10 ?ax max9917eub+ -40? to +85? 10 ?ax r1 47k ? r2 10k ? r g * *optional input resistor r g , is for gain adjustment micropower, two-op-amp instrumentation amplifier r3 10k ? r4 47k ? gain = 1 + r4 r2 for r1 = r4 and r2 = r3 gain = (r1 + r2 + r3 + r4) (r2 + r3) max9916 v ss v dd 3v in- inb+ ina+ outa out ina- outb inb- in+ t ypical operating circuit selector guide part amplifiers per package shutdown mode package max9914exk-t 1n o5 sc70-5 max9915ext-t 1 yes 6 sc70-6 max9916eka-t 2no 8 sot23-8 max9917eub 2 yes 10 max + denotes lead-free package. ?ax is a registered trademark of maxim integrated products, inc.
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 2 _______________________________________________________________________________________ absolute maximum ratings stresses beyond those listed under ?bsolute maximum ratings?may cause permanent damage to the device. these are stress rating s only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specificatio ns is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. power-supply voltage (v dd to v ss ) ......................-0.3v to +6.0v in_+, in_-, out_, shdn_ ............... (v ss - 0.3v) to (v dd + 0.3v) current into in_+, in_- ...................................................... 20ma output short-circuit duration to v dd or v ss ..............continuous continuous power dissipation (t a = +70 c) 5-pin sc70 (derate 3.1mw/ c above +70 c) ............. 247mw 6-pin sc70 (derate 3.1mw/ c above +70 c) ............. 245mw 8-pin sot23 (derate 9.1mw/ c above +70 c)........... 727mw 10-pin ?ax (derate 5.6mw/ c above +70 c) ...........444mw operating temperature range .......................... -40 c to +85 c junction temperature .....................................................+150 c storage temperature range ............................-65 c to +150 c lead temperature (soldering, 10s) ............................... +300 c electrical characteristics (v dd = 1.8v to 5.5v, v ss = 0v, v cm = 0v, v out = v dd / 2, r l = connected to v dd / 2, shdn_ = v dd , t a = +25 c , unless otherwise noted.) (note 1) parameter symbol conditions min typ max units supply voltage range v dd guaranteed by psrr test 1.8 5.5 v v dd = 1.8v 20 max9914/max9915 v dd = 5.5v 20 25 v dd = 1.8v 40 supply current i dd max9916/max9917 v dd = 5.5v 40 50 ? shutdown supply current i dd ( shdn_ ) shdn_ = gnd, max9915/max9917 0.001 0.5 ? input offset voltage v os 0.2 1mv input-offset-voltage matching max9916/max9917 250 ? input bias current i b (note 2) 1 10 pa input offset current i os (note 2) 1 10 pa common mode 1 input resistance r in differential mode, -1mv < v in < +1mv 10 g ? input common-mode range v cm guaranteed by cmrr test v ss - 0.1 v dd + 0.1 v common-mode rejection ratio cmrr -0.1v < v cm < v dd + 0.1v, v dd = 5.5v 70 80 db power-supply rejection ratio psrr 1.8v < v dd < 5.5v 65 85 db 25mv < v out < v dd - 25mv, r l = 100k ? , v dd = 5.5v 95 120 open-loop gain a vol 100mv < v out < v dd - 100mv, r l = 5k ? , v dd = 5.5v 95 110 db r l = 100k ? ? 50 70 output-voltage-swing high v oh v dd - v out r l = 1k ? ? ? 50 70 output-voltage-swing low v ol v out - v ss r l = 1k ? 15 ma
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown _______________________________________________________________________________________ 3 electrical characteristics (continued) (v dd = 1.8v to 5.5v, v ss = 0v, v cm = 0v, v out = v dd / 2, r l = connected to v dd / 2, shdn_ = v dd , t a = +25 c , unless otherwise noted.) (note 1) parameter symbol conditions min typ max units v dd = 1.8v to 3.6v, max9915/max9917 0.4 shdn_ logic low v il v dd = 3.6v to 5.5v, max9915/max9917 0.8 v v dd = 1.8v to 3.6v, max9915/max9917 1.4 shdn_ logic high v ih v dd = 3.6v to 5.5v, max9915/max9917 2 v i il shdn_ = v ss , max9915/max9917 (note 2) 1 shdn_ input bias current i ih shdn_ = v dd , max9915/max9917 500 na output leakage in shutdown i out ( shdn_ ) shdn_ = v ss , v out = 0v to v dd , max9915/max9917 1 500 na gain-bandwidth product 1 mhz phase margin c l = 15pf 45 degrees gain margin c l = 15pf 10 db slew rate 0.5 v/? a v = 1v/v 30 a v = 10v/v 100 r l = 5k ? , a v = 1v/v 100 capacitive-load stability (see the d r i vi ng c ap aci ti ve load s s ecti on) c load no sustained oscillations r iso = 1k ? , a v = 1v/v 100 pf input voltage-noise density f = 1khz 160 nv/ hz n d hz hz s d s sh dd dd shdn_ = 5.5v to 0 step 2s delay time to enable t en v out = 2.7v, v out settles to 0.1%, v dd = 5.5v, v shdn_ = 0 to 5.5v step 10 ? power-up time v dd = 0 to 5.5v step 2 s electrical characteristics (v dd = 1.8v to 5.5v, v ss = 0v, v cm = 0v, v out = v dd / 2, r l = connected to v dd / 2, shdn_ = v dd , t a = -40 c to +85 c , unless otherwise noted.) (note 1) parameter symbol conditions min typ max units supply voltage range v dd guaranteed by psrr test 1.8 5.5 v max9914/max9915 29 supply current i dd max9916/max9917 v dd = 5.5v 60 a shutdown supply current i dd ( shdn_ ) shdn_ = gnd, max9915/max9917 1 a input offset voltage v os 3mv inp ut- o ffset- v ol tag e tem p er atur e c oeffi ci ent tc vos 5 ?/?
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 4 _______________________________________________________________________________________ note 1: specifications are 100% tested at t a = +25 c (exceptions noted). all temperature limits are guaranteed by design. note 2: guaranteed by design, not production tested electrical characteristics (continued) (v dd = 1.8v to 5.5v, v ss = 0v, v cm = 0v, v out = v dd / 2, r l = connected to v dd / 2, shdn_ = v dd , t a = -40 c to +85 c , unless otherwise noted.) (note 1) parameter symbol conditions min typ max units input bias current i b ?0 pa input offset current i os ?0 pa input common-mode range v cm guaranteed by cmrr test v ss - 0.05 v dd + 0.05 v common-mode rejection ratio cmrr -0.05v < v cm < v dd + 0.05v, v dd = 5.5v 60 db power-supply rejection ratio psrr 1.8v < v dd < 5.5v 60 db 25mv < v out < v dd - 25mv, r l = 100k ? , v dd = 5.5v 85 open-loop gain a vol 150mv < v out < v dd - 150mv, r l = 5k ? , v dd = 5.5v 85 db r l = 100k ? 6 output-voltage-swing high v oh v dd - v out r l = 5k ? 90 mv r l = 100k ? 5 output-voltage-swing low v ol v out - v ss r l = 5k ? 90 mv v dd = 1.8v to 3.6v, max9915/max9917 0.4 shdn_ logic low v il v dd = 3.6v to 5.5v, max9915/max9917 0.8 v v dd = 1.8v to 3.6v, max9915/max9917 1.4 shdn_ logic high v ih v dd = 3.6v to 5.5v, max9915/max9917 2 v i il shdn_ = v ss , max9915/max9917 5 na shdn_ input bias current i ih shdn_ = v dd , max9915/max9917 1000 na output leakage in shutdown i out ( shdn_ ) shdn_ = v ss , v out = 0v to v dd , max9915/max9917 1000 na
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown _______________________________________________________________________________________ 5 input offset voltage vs. temperature max9914 toc04 temperature ( c) v os ( v) 60 35 10 -15 -180 -160 -140 -120 -100 -80 -60 -40 -20 0 -200 -40 85 input bias current vs. temperature max9914 toc05 temperature ( c) i b (pa) 60 35 10 -15 -2 -1 0 1 2 3 4 5 6 7 -3 -40 85 i b + i b - input bias current vs. input common-mode voltage max9914 toc06 v cm (v) i b (pa) 3.0 2.5 1.5 2.0 0.5 1.0 0 -4 -3 -2 -1 0 1 2 3 4 5 -5 -0.5 3.5 frequency (hz) psrr (db) 1k 100 10 1 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 -100 0.1 10k power-supply rejection ratio vs. frequency max9914 toc07 common-mode rejection ratio vs. temperature max9914 toc08 temperature ( c) cmrr (db) 60 35 10 -15 20 40 60 80 100 120 140 0 -40 85 frequency (hz) cmrr (db) 10k 1k 100 10 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 -100 1 100k common-mode rejection ratio vs. frequency max9914 toc09 t ypical operating characteristics (v dd = 3v, v ss = v cm = 0v, r l to v dd / 2, t a = +25?, unless otherwise noted.) supply current vs. supply voltage max9914 toc01 v supply (v) i cc ( a) 4.8 4.1 3.3 2.6 5 10 15 20 25 30 35 40 45 50 0 1.8 5.5 t a = +25 c t a = -40 c t a = +85 c t a = +25 c t a = -40 c t a = +85 c dual single shutdown supply current vs. temperature max9914 toc02 temperature ( c) shutdown supply current (na) 60 35 10 -15 -4 -2 0 2 4 6 8 10 12 -6 -40 85 input offset voltage vs. input common-mode voltage max9914 toc03 v cm (v) v os ( v) 2.5 2.0 0.5 1.0 1.5 -750 -500 -250 0 250 500 750 1000 -1000 0 3.0 t a = +25 c t a = -40 c t a = +85 c
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 6 _______________________________________________________________________________________ open-loop gain vs. temperature (r l to v ss ) max9914 toc13 temperature ( c) a vol (db) 60 35 10 -15 20 40 60 80 100 120 140 0 -40 85 r l = 1k ? r l = 5k ? r l = 100k ? 20 40 60 80 120 100 140 160 0 open-loop gain vs. temperature (r l to v dd ) max9914 toc14 temperature ( c) a vol (db) 60 35 10 -15 -40 85 r l = 1k ? r l = 5k ? r l = 100k ? gain and phase vs. frequency (r l = , c load = 15pf) max9914 toc15 frequency (hz) gain (db) phase (degrees) 1m 100k 1k 10k 100 10 -100 -80 -60 -40 -20 0 20 40 60 80 100 -120 -225 -180 -135 -90 -45 0 45 90 135 180 225 -270 1 10m gain a v = 1000v/v phase crosstalk vs. frequency max9914 toc17 frequency (hz) crosstalk (db) 10k 1k 100 -100 -80 -60 -40 -20 0 -120 10 100k max9916/max9917 gain and phase vs. frequency (r l = 5k ? , c load = 100pf) max9914 toc16 frequency (hz) gain (db) phase (degrees) 1m 100k 1k 10k 100 10 -100 -80 -60 -40 -20 0 20 40 60 80 100 -120 -225 -180 -135 -90 -45 0 45 90 135 180 225 -270 1 10m gain a v = 1000v/v phase total harmonic distortion plus noise vs. frequency max9914 toc18 frequency (hz) thd+n (db) 1k 100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 -100 10 10k v out = 2v p-p t ypical operating characteristics (continued) (v dd = 3v, v ss = v cm = 0v, r l to v dd / 2, t a = +25?, unless otherwise noted.) slew rate vs. supply voltage max9914 toc10 supply voltage (v) slew rate (v/ s) 4.8 3.8 2.8 -1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 -1.5 1.8 5.5 output-swing high vs. temperature max9914 toc11 temperature ( c) output voltage swing (mv) 60 35 10 -15 10 100 1000 1 -40 85 r l = 1k ? r l = 5k ? r l = 100k ? r l to v ss v oh = v dd - v out output-swing low vs. temperature max9914 toc12 temperature ( c) output voltage swing (mv) 60 35 10 -15 10 100 1000 1 -40 85 r l = 1k ? r l = 5k ? r l = 100k ? r l to v dd v ol = v out - v ss
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown _______________________________________________________________________________________ 7 voltage-noise density vs. frequency max9914 toc19 frequency (hz) voltage noise (nv/ hz) 10 100 1k 10k 1000 10,000 100 1 100k resistor isolation vs. capacitive load max9914 toc20 c load (pf) r iso ( ? ) 1000 100 500 1000 1500 2000 2500 3000 0 10 10,000 a v = 1v/v for a v = 10v/v no r iso needed power-up settling time max9914 toc21 1 s/div output 500mv/div v dd 1v/div in+ = v dd / 2 a v = 1v/v small-signal gain vs. frequency max9914 toc23 frequency (hz) gain (db) 1m 100k 10k -8 -6 -4 -2 0 2 4 6 8 10 -10 1k 10m a v = 1v/v v out = 100mv p-p c load = 15pf shutdown response max9914 toc22 20 s/div output shdn = 3v 3v 0v 0v 1.5v in+ = v dd / 2 a v = 1v/v 100 10 -3 -2 -1 0 1 2 3 4 -4 1 1000 large-signal gain vs. frequency max9914 toc24 frequency (khz) gain (db) a v = 1v/v v out = 2v p-p c load = 15pf t ypical operating characteristics (continued) (v dd = 3v, v ss = v cm = 0v, r l to v dd / 2, t a = +25?, unless otherwise noted.) small-signal pulse response (c load = 15pf) max9914 toc25 1 s/div output 50mv/div in+ 50mv/div a v = 1v/v small-signal pulse response (c load = 100pf) max9914 toc26 5 s/div output 50mv/div in+ 5mv/div a v = 10v/v
percent overshoot vs. capacitive load max9914 toc29 c load (pf) overshoot (%) 80 60 40 20 2 3 4 5 6 7 1 0 100 r l = 1m ? r l = 100k ? r l = 10k ? output waveform with r iso (c load = 47pf, r iso = 2.3k ? ) max9914 toc30 5 s/div output 50mv/div input 50mv/div a v = 1v/v output waveform without r iso (c load = 47pf) max9914 toc31 5 s/div output 50mv/div in+ 50mv/div a v = 1v/v max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 8 _______________________________________________________________________________________ large-signal pulse response (c load = 15pf) max9914 toc27 5 s/div output 1v/div in+ 1v/div a v = 1v/v large-signal pulse response (c load = 100pf) max9914 toc28 5 s/div output 1v/div in+ 100mv/div a v = 10v/v t ypical operating characteristics (continued) (v dd = 3v, v ss = v cm = 0v, r l to v dd / 2, t a = +25?, unless otherwise noted.)
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown _______________________________________________________________________________________ 9 detailed description featuring a maximized ratio of gain bandwidth to supply current, low operating supply voltage, low input bias current, and rail-to-rail inputs and outputs, the max9914?ax9917 are an excellent choice for preci- sion or general-purpose low-current, low-voltage, bat- tery-powered applications. these cmos devices consume an ultra-low 20? (typ) supply current and a 200? (typ) offset voltage. for additional power conservation, the max9914/max9917 feature a low- power shutdown mode that reduces supply current to 1na (typ), and puts the amplifiers?output in a high- impedance state. these devices are unity-gain stable with a 1mhz gain-bandwidth product driving capacitive loads up to 30pf. the capacitive load can be increased to 100pf when the amplifier is configured for a 10v/v gain. rail-to-rail inputs and outputs the max9914?ax9917 amplifiers all have a parallel- connected n- and p-channel differential input stage that allows an input common-mode voltage range that extends 100mv beyond the positive and negative sup- ply rails, with excellent common-mode rejection. the max9914?ax9917 are capable of driving the out- put to within 5mv of both supply rails with a 100k ? load. these devices can drive a 5k ? load with swings to within 60mv of the rails. figure 1 shows no clipping at the out- put voltage swing of the max9914?ax9917 configured as a unity-gain buffer powered from a single 3v supply. low input bias current the max9914?ax9917 feature ultra-low 1pa (typ) input bias current. the variation in the input bias current is minimal with changes in the input voltage due to very high input impedance (in the order of 1g ? ). applications information driving capacitive loads the max9914?ax9917 amplifiers are unity-gain stable for loads up to 30pf. however, the capacitive load can be increased to 100pf when the amplifier is configured for a minimum gain of 10v/v. applications that require greater capacitive drive capability should use an isolation resistor between the output and the capacitive load (figure 2). also, in unity-gain applications with relatively small r l (about 5k ? ), the capacitive load can be increased up to 100pf. pin max9914 max9915 max9916 max9917 name function 11 in+ noninverting amplifier input 2244v ss negative supply voltage 33 in- inverting amplifier input 44 out amplifier output 56810v dd positive supply voltage ? shdn shutdown 11 outa amplifier output channel a 22 ina- inverting amplifier input channel a 33 ina+ noninverting amplifier input channel a 5 shdna shutdown channel a 6 shdnb shutdown channel b 57 inb+ noninverting amplifier input channel b 68 inb- inverting amplifier input channel b 79 outb amplifier output channel b pin description
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 10 ______________________________________________________________________________________ power-supply considerations the max9914?ax9917 are optimized for single 1.8v to 5.5v supply operation. a high amplifier power-supply rejection ratio of 85db (typ) allows the devices to be powered directly from a battery, simplifying design and extending battery life. power-up settling time the max9914?ax9917 typically require 2s after power-up. supply settling time depends on the supply voltage, the value of the bypass capacitor, the output impedance of the incoming supply, and any lead resis- tance or inductance between components. op amp settling time depends primarily on the output voltage and is slew-rate limited. figure 3 shows the max991_ in a noninverting voltage follower configuration with the input held at midsupply. the output settles in approxi- mately 3.5? for v dd = 3v (see the typical operating characteristics for the power-up settling time graph ). shutdown mode the max9915 and max9917 feature active-low shut- down inputs. the max9915 and max9917 enter shut- down in 2? (typ) and exit shutdown in 10? (typ). the amplifiers?outputs are high impedance in shutdown mode. drive shdn low to enter shutdown. drive shdn high to enable the amplifier. the max9917 dual amplifi- er features separate shutdown inputs. shut down both amplifiers for lowest quiescent current. power-supply bypassing and layout bypass v dd with a 0.1? capacitor to ground as close to the pin as possible to minimize noise. good layout techniques optimize performance by decreasing the amount of stray capacitance and induc- tance to the op amp? inputs and outputs. minimize stray capacitance and inductance, by placing external components close to the ic. figure 1. rail-to-rail output voltage range rail-to-rail output voltage range 200 s/div 3v 0v 3v 0v in_ 1v/div out_ 1v/div v dd = 3v figure 2. using a resistor to isolate a capacitive load from the op amp max9914 max9917 r iso c l r l a v = 1v/v r l r l + r iso figure 3. power-up test configuration max991_ 100k ? 100k ? out in- in+ 0v 5.5v v dd v ss
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown ______________________________________________________________________________________ 11 v dd 8 outb 7 inb- 6 inb+ 5 1 outa ina+ 3 ina- 2 v ss 4 v ss out in- 15v dd in+ max9914 sc70 top view 2 34 v ss out in- 16v dd in+ max9915 sc70 2 34 shdn 5 shdn max9916 sot23 v dd 10 outb 9 inb- 8 shdnb 6 inb+ 7 1 outa 2 ina- v ss 4 ina+ 3 shdna 5 max9917 max shdna shdnb pin configurations chip information max9914 transistor count: 180 max9915 transistor count: 180 max9916 transistor count: 292 max9917 transistor count: 292 process: bicmos
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 12 ______________________________________________________________________________________ package information (the package drawing(s) in this data sheet may not reflect the most current specifications. for the latest package outline info rmation, go to www.maxim-ic.com/packages .) sc70, 5l.eps package outline, 5l sc70 21-0076 1 1 c
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown ______________________________________________________________________________________ 13 package information (continued) (the package drawing(s) in this data sheet may not reflect the most current specifications. for the latest package outline info rmation, go to www.maxim-ic.com/packages .) sc70, 6l.eps package outline, 6l sc70 21-0077 1 1 c
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown 14 ______________________________________________________________________________________ package information (continued) (the package drawing(s) in this data sheet may not reflect the most current specifications. for the latest package outline info rmation, go to www.maxim-ic.com/packages .) sot23, 8l .eps rev. document control no. approval proprietary information title: 3.00 2.60 e c e1 e between 0.08mm and 0.15mm from lead tip. 8. meets jedec mo178. 8 0.60 1.75 0.30 l2 0 e1 e l 1.50 e1 0.65 bsc. 1.95 ref. 0.25 bsc. gauge plane seating plane c c l pin 1 i.d. dot (see note 6) l c l c a2 e1 d detail "a" 5. coplanarity 4 mils. max. note: 7. solder thickness measured at flat section of lead 6. pin 1 i.d. dot is 0.3 mm ? min. located above pin 1. 4. package outline inclusive of solder plating. 3. package outline exclusive of mold flash & metal burr. heel of the lead parallel to seating plane c. 2. foot length measured from lead tip to upper radius of 1. all dimensions are in millimeters. l2 l a1 a 0.45 1.30 0.15 1.45 max 0.28 b 0.90 a2 0.00 a1 0.90 a min symbol 3.00 0.20 2.80 d 0.09 c see detail "a" l c b e d 1 21-0078 1 package outline, sot-23, 8l body 0 0
max9914?ax9917 1mhz, 20?, rail-to-rail i/o op amps with shutdown maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim product. no circu it patent licenses are implied. maxim reserves the right to change the circuitry and specifications without notice at any time. maxim integrated products, 120 san gabriel drive, sunnyvale, ca 94086 408-737-7600 ____________________ 15 2005 maxim integrated products printed usa is a registered trademark of maxim integrated products, inc. package information (continued) (the package drawing(s) in this data sheet may not reflect the most current specifications. for the latest package outline info rmation, go to www.maxim-ic.com/packages .) 10lumax.eps package outline, 10l umax/usop 1 1 21-0061 i rev. document control no. approval proprietary information title: top view front view 1 0.498 ref 0.0196 ref s 6 side view bottom view 0 0 6 0.037 ref 0.0078 max 0.006 0.043 0.118 0.120 0.199 0.0275 0.118 0.0106 0.120 0.0197 bsc inches 1 10 l1 0.0035 0.007 e c b 0.187 0.0157 0.114 h l e2 dim 0.116 0.114 0.116 0.002 d2 e1 a1 d1 min - a 0.940 ref 0.500 bsc 0.090 0.177 4.75 2.89 0.40 0.200 0.270 5.05 0.70 3.00 millimeters 0.05 2.89 2.95 2.95 - min 3.00 3.05 0.15 3.05 max 1.10 10 0.60.1 0.60.1 ? 0.500.1 h 4x s e d2 d1 b a2 a e2 e1 l l1 c gage plane a2 0.030 0.037 0.75 0.95 a1

▲Up To Search▲

Price & Availability of MAX9914EXKT

	To Download MAX9914EXKT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .